How to Configure Network Bridge in Ubuntu |
您所在的位置:网站首页 › ubuntu brctl › How to Configure Network Bridge in Ubuntu |
Linux supports the implementation of a software network bridge to reproduce the function of a network bridge, a networking device that interconnects two or more communication networks or network segments providing a way for them to work as a single network. It acts almost like a network switch, and in a software sense, it is used to implement the concept of a “virtual network switch”. A typical use case of software network bridging is in a virtualization environment to connect virtual machines (VMs) directly to the host server network. This way, the VMs are deployed on the same subnet as the host and can access services such as DHCP and much more. In this article, you will learn different ways to set up a network bridge in Ubuntu and use it within a virtualization environment to create virtual networking in a bridged mode under VirtualBox and KVM, to connect Virtual Machines to the same network as the host. On this page: How to Install Network Bridge Utilities in Ubuntu How to Create a Network Bridge Using NetPlan How to Create a Network Bridge Using Nmcli How to Create a Network Bridge Using nm-connection-editor Tool How to Use the Network Bridge in a Virtualization Software Installing Network Bridge Utilities in UbuntuBegin by installing the bridge-utils package which contains utilities for configuring the Ubuntu ethernet bridge using the apt package manager as shown. $ apt-get install bridge-utilsNext, identify the interface name for your ethernet device using the IP command as shown. $ ip ad OR $ ip add Check Network Interfaces in Ubuntu Creating a Network Bridge Using NetPlan in UbuntuNetplan is a simple and easy-to-use front-end utility for configuring networking in Linux using the YAML format. It currently supports NetworkManager and systemd-netword as backend tools. To configure networking for an interface such as a bridge, edit your netplan configuration file found in /etc/netplan/ directory. The following is an example configuration file, where the renderer is systemd-netword which is the default (replace enp1s0 with your ethernet interface name). network: version: 2 renderer: networkd ethernets: enp1s0: dhcp4: no bridges: br0: dhcp4: yes interfaces: - enp1s0 Netplan Configuration FileSave the configuration file and apply the configuration to enable the bridge network by running the following command. $ sudo netplan applyThen use the brctl command to show all bridges on the system. In this case, the Ethernet interface is automatically added as a port to the bridge. $ sudo brctl show Show Network BridgesIf you want to bring down or deactivate the created network bridge, then delete it using the following commands. $ sudo ip link set enp1s0 up $ sudo ip link set br0 down $ sudo brctl delbr br0 OR $ sudo nmcli conn up Wired\ connection\ 1 $ sudo nmcli conn down br0 $ sudo nmcli conn del br0 $ sudo nmcli conn del bridge-br0 Creating a Network Bridge Using Nmcli in Ubuntunmcli is a widely-used network manager command-line tool to administer NetworkManager (create, show, edit, delete, activate, and deactivate network connections) and displaying network device status. To create a network bridge using nmcli, run the following command. $ sudo nmcli conn add type bridge con-name br0 ifname br0 Create a Network Bridge Using nmcli ToolThen add the Ethernet interface as a port in the bridge as shown (remember to replace enp1s0 with your device name). $ sudo nmcli conn add type ethernet slave-type bridge con-name bridge-br0 ifname enp1s0 master br0 Add a Network Bridge PortsNext, confirm that the bridge has been created by showing all network connections. $ sudo nmcli conn show --active Verify Network BridgeNext, activate the bridge connection as follows (you can use either the connection/interface name or the UUID). $ sudo nmcli conn up br0 OR $ sudo nmcli conn up e7385b2d-0e93-4a8e-b9a0-5793e5a1fda3 Activate Bridge Network ConnectionThen deactivate the Ethernet interface or connection. $ sudo nmcli conn down Ethernet\ connection\ 1 OR $ sudo nmcli conn down 525284a9-60d9-4396-a1c1-a37914d43eff Deactivate Ethernet ConnectionNow try to view active connections once more, the Ethernet interface should now be a slave in the bridge connection as shown in the following screenshot. $ sudo nmcli conn show --active Check Active Network Connections Creating a Network Bridge Using nm-connection-editor ToolTo open the nm-connection-editor application, run the following command from the terminal. $ nm-connection-editorFrom the network connections editor window, click on the + sign to add a new connection profile. Add a New Network ConnectionNext, choose the connection type as Bridge from the drop-down and click Create. Select Network Connection TypeNext, set the bridge connection name and the interface name. Set Bridge Connection NameThen click the Add button to add the bridge slave ports i.e the Ethernet interface as shown in the following screenshot. Select Ethernet as the connection type and click Create. Add a Network Bridge ConnectionNext, set the connection name according to your preference and click Save. Set New Bridge Connection NameUnder bridged connections, the new connection should now appear. Verify New Bridge ConnectionNow if you open the network connection editor once more, the new bridge interface and the slave interface should exist as indicated in the following screenshot. Check Network Bridge ConnectionNext, activate the bridge interface and deactivate the Ethernet interface, using the nmcli command. $ sudo nmcli conn up br0 $ sudo nmcli conn down Ethernet\ connection\ 1 How to Use a Network Bridge in a Virtualization SoftwareAfter setting up a network bridge (virtual network switch), you can use it in a virtualization environment such as Oracle VirtualBox and KVM to connect VMs to the host network. Using a Network Bridge in Oracle VirtualBoxOpen VirtualBox, then from the list of VMs, select a VM, then click on its settings. From the settings window, go to the Network option and select an adapter (e.g Adapter 1). Then check the option Enable Network Adapter, set the value of the attached to the field to Bridged Adapter, then set the Name of the bridged interface (e.g br0) as indicated in the following screenshot. Then click Ok. Configure VM to Use Bridge Network in VirtualBox Using a Network Bridge in KVMYou can use the new network bridge under KVM by adding the --network=bridge=br0 option while creating a new virtual machine, using the virt-install command. # virt-install --virt-type=kvm --name Ubuntu18.04 --ram 1536 --vcpus=4 --os-variant=ubuntu18.04 --cdrom=/path/to/install.iso --network=bridge=br0,model=virtio --graphics vnc --disk path=/var/lib/libvirt/images/ubuntu18.04.qcow2,size=20,bus=virtio,format=qcow2From the web console, it will be select automatically. Besides, you can also configure a network bridge using the virsh command-line tool, and a VM’s XML configuration file. For more details, read the netplan and nmcli man pages (by running man netplan and man nmcli) as well as virtual networking in libvirt and virtual networking in VirtualBox. You can post any queries to us via the comment section below. |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |